Engineering Data

Sleeve material properties.
FEP, PFA, PTFE and conductive PTFE.

One table for engineers comparing Fluoron heat-shrink sleeves: Fluoro-Clear (FEP), Fluoro-Flex (PFA), Fluoro-Wear (virgin PTFE) and Fluoro-Stat (carbon-filled PTFE). Temperature, color, FDA and medical grade, static and electrical behavior, thermal conductivity and mechanical properties, side by side.

Fluoron heat-shrink sleeves on rolls: black conductive PTFE, white PTFE and clear FEP.
Black Fluoro-Stat, white Fluoro-Wear and clear Fluoro-Clear sleeves
A / Property table

Fluoron sleeve material comparison

On a phone, swipe sideways to see all four materials.

Fluoron heat-shrink sleeve material properties: Fluoro-Clear FEP, Fluoro-Flex PFA, Fluoro-Wear PTFE, Fluoro-Stat conductive PTFE
Property 01 / FEPFluoro-ClearFEP 02 / PFAFluoro-FlexPFA 03 / PTFEFluoro-WearVirgin PTFE 04 / PTFE-CFluoro-StatCarbon-filled PTFE
Fluoron sleeve ratingsOur product ratings for the finished heat-shrink sleeve.
Base materialFEP (fluorinated ethylene propylene)PFA (perfluoroalkoxy)Virgin PTFE (polytetrafluoroethylene)Carbon-filled PTFE (conductive)
Color / appearanceClear, transparentTranslucent (natural)Opaque whiteOpaque black
Max continuous service tempFluoron rating375°F / 190°C500°F / 260°C500°F / 260°C500°F / 260°C
Wall thickness0.020″ or 0.060″0.060″0.060″0.060″
Construction / roll diameterSeamless to 18″; seamed beyondSeamless to 18″; seamed beyondSeamed, 5″ and upSeamed, 5″ and up (to 60″ on request)
Coefficient of frictionFluoron, typical~0.18~0.10≤ 0.05~0.08
Release / non-stickGoodGoodExcellentExcellent
Abrasion resistanceGoodBetterExcellentExcellent: over 10× FEP in Fluoron wear testing
BondingEtched for adhesive bonding, or unetchedSelected with Fluoron engineeringHeat-shrink fit; bonded when service requiresHeat-shrink fit; bonded to a grounded roll for static control
Compliance
FDA food contact21 CFR 177.1550YesYesYesYes
Medical grade (USP Class VI)On requestOn requestOn requestNot offered
FlammabilityUL 94VTM-0 (film)V-0V-0V-0 *
Electrical and staticResin typicals, except Fluoro-Stat surface resistivity (Fluoron test).
Static behaviorInsulator: builds static on dry websInsulator: builds static on dry websInsulator: builds static on dry websStatic-dissipative: bleeds charge to a grounded roll
Surface resistivityASTM D257, Ω/sq> 1016> 10181018102 (Fluoron test)
Volume resistivityASTM D257, Ω·cm> 1018> 1018> 1018104 *
Dielectric constantASTM D150, 1 MHz2.02.032.1Not applicable (conductive)
Dielectric strengthASTM D149, short time70 kV/mm (1,800 V/mil), 0.5 mm film80 kV/mm (2,000 V/mil), 0.25 mm film16 kV/mm (Chemours typical)Not applicable (conductive)
ThermalResin typicals.
Thermal conductivityW/m·K (Btu·in/h·ft²·°F)0.195 (1.35)0.19 (1.32)0.25 (1.7)0.65 (4.5) *
Melting point500–536°F (260–280°C)581°F (305°C)627°F (331°C)635°F (335°C) *
Physical and mechanicalResin typicals.
Specific gravityASTM D7922.152.152.22.08 *
Tensile strength, 73°F21 MPa (3,000 psi)25–28 MPa (3,600–4,000 psi)20 MPa (2,900 psi)13 MPa (1,900 psi) *
Elongation at break300%300%200–400%75% *
HardnessShore D, ASTM D224055556062 *
Water absorption, 24 hASTM D570< 0.01%< 0.03%< 0.01%0.05% *
OpticalResin typicals.
Light transmission96% (ASTM E424, film)91–96% visible (1-mil film)OpaqueOpaque
Refractive indexASTM D5421.341–1.3471.350——

Sleeve ratings, coefficient of friction and Fluoro-Stat surface resistivity and abrasion are Fluoron values. Other values are typical published values for the base resin, measured on molded or film samples. They are for comparison, not specification limits. Finished-sleeve values can differ with wall thickness, processing and service conditions.

* Typical published values for 25% carbon-filled PTFE. Fluoro-Stat filler content is proprietary; contact Fluoron engineering for application data.

FEP, PFA and PTFE sleeves are made from resins that comply with FDA 21 CFR 177.1550 (perfluorocarbon resins). Fluoro-Stat is FDA compliant. Compliance letters and medical-grade (USP Class VI) material are available on request.

B / Reading the table

What usually decides the material

Four questions that narrow it down fast.

Temperature
Running above 375°F?

Fluoro-Clear FEP is rated to 375°F. Above that, go to Fluoro-Flex PFA, Fluoro-Wear PTFE or Fluoro-Stat, all rated to 500°F.

Static
Dry web or static shocks?

FEP, PFA and virgin PTFE are insulators. Fluoro-Stat, at 102 Ω/sq, bleeds charge into a grounded roll.

Visibility
Need to see the roll underneath?

Fluoro-Clear FEP is transparent, with about 96% light transmission, so you can inspect the roll body and nip.

Wear
Abrasive or high-wear position?

Fluoro-Wear and Fluoro-Stat carry the best release and abrasion resistance. Fluoro-Stat showed over 10× the wear resistance of FEP in our testing.

C / Sources

Where the numbers come from

Resin data from the resin manufacturer and published typicals; sleeve ratings from Fluoron.

  1. Chemours, Teflon™ FEP Fluoropolymer Film Properties Bulletin
  2. Chemours, Teflon™ PFA Properties Handbook
  3. Chemours, Properties of Teflon™ fluoropolymers (PTFE, FEP, PFA)
  4. Typical properties of unfilled and 25% carbon-filled PTFE
  5. U.S. FDA, 21 CFR 177.1550 Perfluorocarbon resins
  6. Fluoron, Fluoro-Stat 102 technical sheet (surface resistivity, abrasion testing)
Product detail

All four sleeves, best-fit positions and sizing.

Material guide

How each fluoropolymer ends up on different rollers.

Static control

When to choose conductive PTFE over standard PTFE.

Resources

Downloadable product sheets and installation guides.